| View previous topic :: View next topic |
| Author |
Message |
cccc
Initiate
Joined: 02 Jul 2007
Posts: 92
|
 Posted: Sat Aug 31, 2013 9:58 am Post subject: enable UDMA Mode 6 (Ultra ATA/133) |
 |
|
Hi
I have WIN 7 Prof, this motherboard and 500GB hard disk: | Code: |
Motherboard ---------------------------------------------------------------
[Computer]
Computer Brand Name: LENOVO 1578E1G
[Motherboard]
Motherboard Model: LENOVO
Motherboard Chipset: Intel H61 (Cougar Point)
Motherboard Slots: 4xPCI Express x1, 1xPCI Express x16
PCI Express Version Supported: v2.0
USB Version Supported: v2.0
[PCH Features]
USB Port Count: 10 ports
RAID Capability: Not Supported
SATA Ports 2 and 3: Not Supported
SATA Port 1 6 Gb/s: Not Supported
SATA Port 0 6 Gb/s: Not Supported
PCI Interface: Not Supported
PCI Express Ports 5 and 6: Supported
USB Redirect (USBr): Not Supported
Intel Anti-Theft Technology: Supported
PCI Express Ports 7 and 8: Not Supported
PCH Integrated Graphics Support: Supported
Data Center Manageability Interface (DCMI): Supported
Node Manager: Supported
[BIOS]
BIOS Manufacturer: American Megatrends
BIOS Date: 08/10/2012
BIOS Version: 9QKT39AUS
EFI BIOS: Capable
Super-IO/LPC Chip: Winbond/Nuvoton NCT6776
WDC WD5003ABYX-01WERA1 ----------------------------------------------------
[General Information]
Drive Controller: Serial ATA 3Gb/s
Drive Model: WDC WD5003ABYX-01WERA1
Drive Revision: 01.01S02
Drive Serial Number: WD-WMAYP3393761
Drive Capacity: 476,940 MBytes (500 GB)
Drive Capacity [MB]: 476940
Media Rotation Rate: 7200 RPM
[Drive Geometry]
Number of Cylinders: 16383
Number of Heads: 16
Sectors Per Track: 63
Bytes Per Sector: Unknown
Bytes Per Track: Unknown
Number Of ECC Bytes: 50
Number of Sectors: 16514064
Total 32-bit LBA Sectors: 268435455
Total 48-bit LBA Sectors: 976773168
Cache Buffer Size: N/A
Controller Type: Not Specified
[Transfer Modes]
Sectors Per Interrupt: Total: 16, Active: 16
Max. PIO Transfer Mode: 4
Multiword DMA Mode: Total: 2, Active: -
Singleword DMA Mode: Total: -, Active: -
Ultra-DMA Mode: Total: 6 (ATA-133), Active: 5 (ATA-100)
Max. Multiword DMA Transfer Rate: 16.7 MBytes/s
Max. PIO with IORDY Transfer Rate: 16.7 MBytes/s
Max. PIO w/o IORDY Transfer Rate: 16.7 MBytes/s
Transfer Width: 16-bit
Native Command Queuing: Supported, Max. Depth: 32
TRIM Command: Not Supported
[Device flags]
Fixed Drive: Present
Removable Drive: Not Present
Magnetic Storage: Present
LBA Mode: Supported
DMA Mode: Supported
IORDY: Supported
IORDY Disableable: Supported
[Features]
Write Cache: Present, Active
S.M.A.R.T. Feature: Present, Active
Security Feature: Present, Inactive
Removable Media Feature: Not Present, Disabled
Power Management: Present, Active
Advanced Power Management: Present, Active
Packet Interface: Not Present, Disabled
Look-Ahead Buffer: Present, Active
Host Protected Area: Present, Enabled
Power-Up In Standby: Supported, Inactive
Automatic Acoustic Management: Not Suppported, Inactive
48-bit LBA: Supported, Active
[Self-Monitoring, Analysis and Reporting Technology]
Raw Read Error Rate: 200/51, Worst: 200
Spin Up Time: 138/21, Worst: 137 (Data = 4083)
Start/Stop Count: 100/Always OK, Worst: 100 (Data = 36)
Reallocated Sector Count: 200/140, Worst: 200
Seek Error Rate: 100/Always OK, Worst: 253
Power-On Hours/Cycle Count: 100/Always OK, Worst: 100 (Data = 23)
Spin Retry Count: 100/Always OK, Worst: 253
Calibration Retry Count: 100/Always OK, Worst: 253
Power Cycle Count: 100/Always OK, Worst: 100 (Data = 34)
Power-Off Retract Count: 200/Always OK, Worst: 200 (Data = 10)
Load/Unload Cycle Count: 200/Always OK, Worst: 200 (Data = 25)
Temperature 112/Always OK, Worst: 109 (Data = 31.0 °C)
Reallocation Event Count: 200/Always OK, Worst: 200
Current Pending Sector Count: 200/Always OK, Worst: 200
Off-Line Uncorrectable Sector Count: 100/Always OK, Worst: 253
UltraDMA/SATA CRC Error Rate: 200/Always OK, Worst: 200
Write/Multi-Zone Error Rate: 100/Always OK, Worst: 253
|
Using HD Tune and get the following information:
--------------------------------------------------------------
HD Tune: WDC WD5003ABYX-01WERA1
Firmware version : 01.01S02
Serial number : WD-WMAYP3393774
Capacity : 465.8 GB (~500.1 GB)
Buffer size : n/a
Standard : ATA/ATAPI-8 - SATA II
Supported mode : UDMA Mode 6 (Ultra ATA/133)
Current mode : UDMA Mode 5 (Ultra ATA/100)
S.M.A.R.T : yes
48-bit Address : yes
Read Look-Ahead : yes
Write Cache : yes
Host Protected Area : yes
Device Configuration Overlay : yes
Automatic Acoustic Management: no
Power Management : yes
Advanced Power Management : yes
Power-up in Standby : yes
Security Mode : yes
Firmware Upgradable : yes
Partition : 1
Drive letter :
Label :
Capacity : 1200 MB
Usage : 0.00%
Type : NTFS
Bootable : Yes
Partition : 2
Drive letter : C:\
Label : Windows7_OS
Capacity : 456959 MB
Usage : 23.17%
Type : NTFS
Bootable : No
Partition : 3
Drive letter : Q:\
Label : "Lenovo_Recovery"
Capacity : 18780 MB
Usage : 62.09%
Type : NTFS
Bootable : No
--------------------------------------------------------------
Why UDMA Mode 6 (Ultra ATA/133) is not active?
Last edited by cccc on Sat Aug 31, 2013 10:42 am; edited 2 times in total |
|
| Back to top |
|
 |
Toby B.
Lead Mobo-fu Master
Joined: 16 Dec 2001
Posts: 14002
Location: Maine
|
| Posted: Sat Aug 31, 2013 10:38 am Post subject: |
|
|
Chances are where it's probably a butchered AMI BIOS, there will be little luck getting the functionality you are looking for.
evasive, our resident BIOS guy is here less now due to real life stuff.. Best advice I can give, post at www.wimsbios.com, you might receive a speedier response..
_________________
We Help You. You Can Help Us!
Read the rules prior to posting
Tell your newsgroup or mailing list
Link to us from your pages |
|
| Back to top |
|
|
evasive
Mobo-fu Master
Joined: 06 May 2001
Posts: 36479
Location: Netherlands, Breda
|
| Posted: Sat Aug 31, 2013 1:36 pm Post subject: |
|
|
Why are you using something that confuses SATA and PATA devices? Your disk is not even connected to the UDMA mode 6 port, it is connected to a SATA2 port that is ATA-300 if you want to botch the standards again. I don't know why HD tune is reporting things like this, maybe time for a newer version...
_________________
We hate rut, but we fear change.
System error, strike any user to continue... |
|
| Back to top |
|
|
cccc
Initiate
Joined: 02 Jul 2007
Posts: 92
|
| Posted: Sat Aug 31, 2013 3:08 pm Post subject: |
|
|
Yep, may hard disk is connected to a SATA2 port and the connector is in BIOS on AHCI.
I don't have any PATA (IDE) ports on my mainboard.
HD Tune is quite old and displays a false information. |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
|
