The Mother Board
Project Panzerbox: A Tribute to Wolfenstein
Goto page Previous  1, 2, 3, 4, 5, 6, 7, 8, 9  Next
 
Post new topic   Reply to topic    The Mother Board Forum Index -> System Modification
View previous topic :: View next topic  
Author Message
AmEv
Black Belt
Black Belt


Joined: 20 Jun 2009
Posts: 654
Location: Wanting to be at these forums, but not as active as they

PostPosted: Mon Oct 26, 2009 4:03 pm    Post subject: Reply with quote

Good, very good.

I don't know if you intended it or not, but the PSU fan behind the "gears" seems to give it a Swastika look.

*In a good way eye roll lol wink
_________________
I'm gonna get my new hardware. And my worklog here.
Back to top
View user's profile Send private message Visit poster's website
Mnpctech.com
Black Belt
Black Belt


Joined: 18 May 2009
Posts: 558

PostPosted: Sat Oct 31, 2009 3:51 am    Post subject: Reply with quote

I didn't even notice that! Thanks for commenting

Our HD arrived, Western Digital Caviar Blue WD2500AAJS 250GB 7200 RPM 8MB Cache SATA 3.0Gb

$44.99 shipped!

http://www.newegg.com/Product/Product.aspx?Item=N82E16822136113

Back to top
View user's profile Send private message
Mnpctech.com
Black Belt
Black Belt


Joined: 18 May 2009
Posts: 558

PostPosted: Mon Nov 02, 2009 6:22 pm    Post subject: Reply with quote

Nate started the system install Sunday afternoon. The Thermalright Ultra 120 Extreme Revision A HSF clears the chassis.


250mm fan draws out the warm air from the Ultra 120 Extreme Revision A




Thermalright has since updated the mounting bracket to turn the HSF 90 degrees and avoid blocking DDR in first two slots


We'll be using these new PC Cable management clamps
http://www.mnpctech.com/CableClamp.html



Nate from CustomPCMax.com
Back to top
View user's profile Send private message
Mnpctech.com
Black Belt
Black Belt


Joined: 18 May 2009
Posts: 558

PostPosted: Tue Nov 03, 2009 4:30 am    Post subject: Reply with quote

Nate and I agreed top of Heat sink fins looks naked, it needs something... More on that later :thumb:

Back to top
View user's profile Send private message
Mnpctech.com
Black Belt
Black Belt


Joined: 18 May 2009
Posts: 558

PostPosted: Wed Nov 04, 2009 4:40 pm    Post subject: Reply with quote

We'll be painting the 5.1 surround sound headset we received from Psyko Audio with matching camo

Back to top
View user's profile Send private message
THRASHER2
Forum Terminator


Joined: 10 Jul 2007
Posts: 6663
Location: Long Beach,CA in the Mod Garage OverClocking

PostPosted: Wed Nov 04, 2009 8:13 pm    Post subject: Reply with quote

Those are some KOOL head-phones lachen
_________________

THRASHER2's benchmark scores
Project T2's Spinner Case
Back to top
View user's profile Send private message AIM Address Yahoo Messenger MSN Messenger
Mnpctech.com
Black Belt
Black Belt


Joined: 18 May 2009
Posts: 558

PostPosted: Fri Nov 06, 2009 10:36 am    Post subject: Reply with quote

The dissection of a Psyko Audio Headset, before prepped for Camo paint

The padded ear cup pads can be popped off with their pivoting bases (grab around the top of the plastic ring and pull it out).









4 screws total, 2 on each side fasten on outter Silver trim piece



4, screw locations to be removed.







The clear cup cover is easily removed, once the outter trim piece is removed.



The clear cover pops off (push a small flat head screw driver into the gaps to pry off).





The pads are peeled off. I used a small flat head screw driver to pry up the edge first.



You can peel off the top 5 pads to reveal 5 screws holding on the top Silver cover.







5x 30mm diam. 32 ohm. speakers project sound into your skull

Back to top
View user's profile Send private message
Mnpctech.com
Black Belt
Black Belt


Joined: 18 May 2009
Posts: 558

PostPosted: Sat Nov 07, 2009 5:12 am    Post subject: Reply with quote

I agree! After the pads are removed, the headset is re-assembled before being masked off before camo paint job. It's easier to apply the camo stencils when it's all assembled without the pads

Back to top
View user's profile Send private message
Mnpctech.com
Black Belt
Black Belt


Joined: 18 May 2009
Posts: 558

PostPosted: Sat Nov 07, 2009 5:21 pm    Post subject: Reply with quote

For tidying up the PSU cables, I'm using the small size PC Cable Clamps, they hold approximately 1" bundle

PC Cable Clamp Link
http://www.mnpctech.com/CableClamp.html











Back to top
View user's profile Send private message
Mnpctech.com
Black Belt
Black Belt


Joined: 18 May 2009
Posts: 558

PostPosted: Thu Nov 12, 2009 1:54 pm    Post subject: Reply with quote

Brad sent me progress on the Camo paint on the Pysko Audio head phones. These will look awesome!

Headset


Amp


Mic
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    The Mother Board Forum Index -> System Modification All times are GMT - 8 Hours
Goto page Previous  1, 2, 3, 4, 5, 6, 7, 8, 9  Next
Page 7 of 9

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2002 phpBB Group