Project Panzerbox: A Tribute to Wolfenstein

Resources, guides, discussions for modding your system.

Postby AmEv » Mon Oct 26, 2009 4:03 pm

Good, very good.

I don't know if you intended it or not, but the PSU fan behind the "gears" seems to give it a Swastika look.

*In a good way :roll: :lol: :wink:
I'm gonna get my new hardware. And my worklog here.
AmEv
Black Belt
Black Belt
 
Posts: 654
Joined: Sat Jun 20, 2009 4:53 pm
Location: Wanting to be at these forums, but not as active as they

Postby Mnpctech.com » Sat Oct 31, 2009 3:51 am

I didn't even notice that! Thanks for commenting

Our HD arrived, Western Digital Caviar Blue WD2500AAJS 250GB 7200 RPM 8MB Cache SATA 3.0Gb

$44.99 shipped!

http://www.newegg.com/Product/Product.a ... 6822136113

Image
Mnpctech.com
Black Belt
Black Belt
 
Posts: 561
Joined: Mon May 18, 2009 7:20 am

Postby Mnpctech.com » Mon Nov 02, 2009 6:22 pm

Nate started the system install Sunday afternoon. The Thermalright Ultra 120 Extreme Revision A HSF clears the chassis.
Image

250mm fan draws out the warm air from the Ultra 120 Extreme Revision A
Image

Image

Thermalright has since updated the mounting bracket to turn the HSF 90 degrees and avoid blocking DDR in first two slots
Image

We'll be using these new PC Cable management clamps
http://www.mnpctech.com/CableClamp.html

Image

Nate from CustomPCMax.com
Image
Mnpctech.com
Black Belt
Black Belt
 
Posts: 561
Joined: Mon May 18, 2009 7:20 am

Postby Mnpctech.com » Tue Nov 03, 2009 4:30 am

Nate and I agreed top of Heat sink fins looks naked, it needs something... More on that later :thumb:

Image
Mnpctech.com
Black Belt
Black Belt
 
Posts: 561
Joined: Mon May 18, 2009 7:20 am

Postby Mnpctech.com » Wed Nov 04, 2009 4:40 pm

We'll be painting the 5.1 surround sound headset we received from Psyko Audio with matching camo

Image
Mnpctech.com
Black Belt
Black Belt
 
Posts: 561
Joined: Mon May 18, 2009 7:20 am

Postby THRASHER2 » Wed Nov 04, 2009 8:13 pm

Those are some KOOL head-phones :)
THRASHER2
Forum Terminator
 
Posts: 6663
Joined: Tue Jul 10, 2007 10:22 pm
Location: Long Beach,CA in the Mod Garage OverClocking

Postby Mnpctech.com » Fri Nov 06, 2009 10:36 am

The dissection of a Psyko Audio Headset, before prepped for Camo paint

The padded ear cup pads can be popped off with their pivoting bases (grab around the top of the plastic ring and pull it out).

Image

Image

Image

Image

4 screws total, 2 on each side fasten on outter Silver trim piece

Image

4, screw locations to be removed.

Image

Image

Image

The clear cup cover is easily removed, once the outter trim piece is removed.

Image

The clear cover pops off (push a small flat head screw driver into the gaps to pry off).

Image

Image

The pads are peeled off. I used a small flat head screw driver to pry up the edge first.

Image

You can peel off the top 5 pads to reveal 5 screws holding on the top Silver cover.

Image

Image

Image

5x 30mm diam. 32 ohm. speakers project sound into your skull

Image
Mnpctech.com
Black Belt
Black Belt
 
Posts: 561
Joined: Mon May 18, 2009 7:20 am

Postby Mnpctech.com » Sat Nov 07, 2009 5:12 am

I agree! After the pads are removed, the headset is re-assembled before being masked off before camo paint job. It's easier to apply the camo stencils when it's all assembled without the pads

Image
Mnpctech.com
Black Belt
Black Belt
 
Posts: 561
Joined: Mon May 18, 2009 7:20 am

Postby Mnpctech.com » Sat Nov 07, 2009 5:21 pm

For tidying up the PSU cables, I'm using the small size PC Cable Clamps, they hold approximately 1" bundle

PC Cable Clamp Link
http://www.mnpctech.com/CableClamp.html


Image


Image


Image


Image
Mnpctech.com
Black Belt
Black Belt
 
Posts: 561
Joined: Mon May 18, 2009 7:20 am

Postby Mnpctech.com » Thu Nov 12, 2009 1:54 pm

Brad sent me progress on the Camo paint on the Pysko Audio head phones. These will look awesome!

Headset
Image

Amp
Image

Mic
Image
Mnpctech.com
Black Belt
Black Belt
 
Posts: 561
Joined: Mon May 18, 2009 7:20 am

PreviousNext

Return to System Modification

Who is online

Users browsing this forum: Exabot [Bot] and 0 guests