The Mother Board

Motherboards.org forums. Free tech support, motherboard ID, and more.
It is currently Mon Aug 20, 2018 1:14 am

All times are UTC - 8 hours




Post new topic Reply to topic  [ 51 posts ]  Go to page 1, 2, 3, 4, 5, 6  Next
Author Message
PostPosted: Thu Oct 29, 2009 4:34 am 
Offline
Black Belt
Black Belt

Joined: Mon May 18, 2009 7:20 am
Posts: 570
I've started the build for Cooler Master's media suite at 2010 CES. The D-9 concept was mine after seeing the movie.

I should know by first week of November what hardware CM will be sending me.

Image

Image
Conceptual drawing by E.E.L. Ambiense


Case Mods & Supplies used in this project by Mnpctech.com

Machined Aluminum Computer Case Feet Link

Image

Acoustical Sound Proofing Sheets for your PC

Image

Mnpctech is now stocking clear and colored sheets of cast acrylic for window mods

http://www.mnpctech.com/colored_acrylic ... indow.html

Image

This is the Honeycomb Modders Meshwe used.

Image

PC Cable management clamps
http://www.mnpctech.com/CableClamp.html

The canvas for this PC build is the Cooler Master 840 ATCS

Image

Adding window to Cooler master 840 ATCS
Image

Using tape roll to make curved corner
Image

Make first initial cut with your Dremel and cutting wheel, to allow use of Jigsaw and cut the window more efficiently

Image

You have created slot, this allows using a Jigsaw w/ 18 TPI cutting blade
Image


Image

Using a Jigsaw is much quicker than using a Dremel to cut your window
Image


Top
 Profile  
Reply with quote  
 Post subject:
PostPosted: Thu Nov 05, 2009 9:39 am 
Offline
Black Belt
Black Belt

Joined: Mon May 18, 2009 7:20 am
Posts: 570
I've cut the window from Lexan. It's tougher than plexiglass/acrylic, but 2 or 3 times more expensive. It won't shatter or crack "easily" You can buy Lexan sheets at Home Depot, Lowes and some hardware stores like Ace.

The window will be fastened with 1/4" socket head screws, for reinforced armour look

Using center punch to mark each fastener hole.

Image

Roper Whitney No. 5 Jr Hand Punch kit available here
Hand punch (estimate $60 new)

Image

Image

"Look Ma, No deburring needed!"
Image

The benefit of using Lexan is that you can drill or hand punch it without cracking it.

Image

Clean hole cut! I love Lexan.

Image

Image

Ironically our concept drawing calls for bullet holes in the Lexan "bullet proof" window...lol


Top
 Profile  
Reply with quote  
 Post subject:
PostPosted: Thu Nov 19, 2009 6:08 am 
Offline
Black Belt
Black Belt

Joined: Mon May 18, 2009 7:20 am
Posts: 570
Cooler Master's hardware list for their CES show display

1 x Intel Core 2 Duo E8500 Wolfdale 3.16GHz 6MB L2 Cache LGA 775 65W Dual-Core Processor
1 x Intel Extreme Series DX48BT2 X48 Motherboard
1 x Silent Pro RS-600-AMBA-D3
1 x CM MITX Cooler 38mm tall (will be replaced with future V series cooler)
1 x Sapphire ATI Radeon 4870 512MB
1 x 4GB DDR3 Kingston 1600mhz memory kit
1 x WD 500GB HDD
1 x DVD drive

Silent Pro RS-600 Watt-AMBA-D3 PSU
http://www.newegg.com/Product/Product.a ... 6817171036

Image

Image

Image

Are you a fan of the Black Ribbon power cables?

Image


Top
 Profile  
Reply with quote  
 Post subject:
PostPosted: Thu Nov 19, 2009 10:56 am 
Offline
Black Belt
Black Belt

Joined: Mon May 18, 2009 7:20 am
Posts: 570
The concept called for bullet holes in the window

Image

Using 3/8" drill bit
Image

Image

Using wire cutter to make cracks around the hole
Image

Etching Rotary Tool (or Dremel) Engraving Bits
Image

Using the dremel to emulate some cracks
Image


Top
 Profile  
Reply with quote  
 Post subject:
PostPosted: Fri Nov 20, 2009 1:16 pm 
Offline
Black Belt
Black Belt

Joined: Mon May 18, 2009 7:20 am
Posts: 570
I'm adding bullet holes to the case too, so I drilled holes in the 840's aluminum panel. I then used a tin snip and needle nose plier to cut and rip the 3/8" hole open

Image

Image

Image


Top
 Profile  
Reply with quote  
 Post subject:
PostPosted: Fri Nov 20, 2009 4:26 pm 
Offline
Black Belt
Black Belt

Joined: Sat Jun 20, 2009 4:53 pm
Posts: 654
Location: Wanting to be at these forums, but not as active as they
Now, to make some matching ones on the other side (if possible...)

That would complete it.

_________________
I'm gonna get my new hardware. And my worklog here.


Top
 Profile  
Reply with quote  
 Post subject:
PostPosted: Sat Nov 28, 2009 8:24 am 
Offline
Black Belt
Black Belt

Joined: Mon May 18, 2009 7:20 am
Posts: 570
Image

I've actually decided to modify the original concept case to reflect the theme of this Prawn weapon from the movie. The case will have reinforced panels and Orange/Black/White color scheme. One of the easiest steps to fit this theme was replacing the OEM handle on the Cooler Master 840 motherboard tray with machined aluminum handle. I had one spare handle left over from our previous stock. The new version has been revised with rounded finger grips, as shown here, http://www.mnpctech.com/MnpctechBilleth ... ooved.html

Image

Image

Image

I'm using 1/4" drill bit
Image

Image

Image

Image

Image

Image

Image


Top
 Profile  
Reply with quote  
 Post subject:
PostPosted: Sun Nov 29, 2009 4:35 am 
Offline
Black Belt
Black Belt

Joined: Mon May 18, 2009 7:20 am
Posts: 570
CM is planning to show their new V-series cooler, they wouldn't reveal the model to me.

I may rig a Cat Food can as cpu cooler, just for joke when they open the case....lol

Cooler Master only sent 1 hard drive, so no sense in keeping the HD bay!

Use 1/8" drill bit to remove HD bay

Image

Image


Top
 Profile  
Reply with quote  
 Post subject:
PostPosted: Sun Nov 29, 2009 8:53 am 
Offline
Black Belt
Black Belt

Joined: Sat Jun 20, 2009 4:53 pm
Posts: 654
Location: Wanting to be at these forums, but not as active as they
How about a can of chili? :o :o :lol: :twisted:

_________________
I'm gonna get my new hardware. And my worklog here.


Top
 Profile  
Reply with quote  
 Post subject:
PostPosted: Sun Nov 29, 2009 3:24 pm 
Offline
Black Belt
Black Belt

Joined: Mon May 18, 2009 7:20 am
Posts: 570
The Prawn love cat food, they trade weapons for cat food..lol

1/4" thick acrylic sheets will act as reinforced segments of the side panels.
Image

Heres a close up of the vertical blade cutting 1/4" acrylic sheet
Image

These edges are not acceptable
Image

Black & Decker Mouse Sander with Medium grit sandpaper
Image

Thats better!
Image

Starting on other side tonight, this side still needs exploded hole, and I need to get more 1/4" socket head screws. Those will be countersunk
Image


Top
 Profile  
Reply with quote  
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 51 posts ]  Go to page 1, 2, 3, 4, 5, 6  Next

All times are UTC - 8 hours


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group