Unlocking Your Athlon XP by Tulatin

Techniques, tips, and advice for the performance PC enthusiast on overclocking.

Moderator: The Mod Squad

Postby joshvee » Sun Sep 21, 2003 12:49 pm

Tulatin wrote:the multi? Usually i wouldn't bother raising it, and just keep boosing the fsb in stead. Other than that, so long as you lower the fsb a little as you raise it, there should be no danger zone.


ok now this is the part im confused with....if u can so easily raise the multiplier why does everyone go for a FSB increase instead....whats the advantage of increasing the FSB instead of the multiplier....

wouldn't it be more stable increasing the multiplier? because the ram, video card FSB ect' remain at a safe MHz?
Image
joshvee
Black Belt 4th Degree
Black Belt 4th Degree
 
Posts: 4411
Joined: Sat Jul 12, 2003 11:13 pm
Location: Australia

Postby Tulatin » Sun Sep 21, 2003 12:54 pm

first josh, higher fsb = higher speed everything communicates, and most times, higher ram speeds so - more bandwidth. As to the increasing of the clocks of video and pci, some of today's new baords, namely abit ones allow you to lock the agp at 67 and the pci at 33, making sure that your video and add in cards don't get damaged.
Tulatin
Enlightened Master
Enlightened Master
 
Posts: 14664
Joined: Wed Dec 11, 2002 2:29 pm
Location: Canada

Postby subtool » Thu Feb 12, 2004 11:00 pm

I have been reading about unlocking the barton 2500+ and i have been finding contradicting information. Is this http://anitec.ca/default.asp?ShowPage=P ... =1&pid=680 chip unlockable with the methods you have stated? Is there chips that are totally impossible to unlock? (Great thread by the way)
NF7-S
Barton 2500+
Enermax 430W PSU
MSI FX 5200
2X 256 Samsung DDR 400
subtool
Initiate
Initiate
 
Posts: 50
Joined: Fri Jan 30, 2004 2:29 am
Location: The North, Eh.

Postby Tulatin » Fri Feb 13, 2004 12:56 am

Thanks for the compliment - this was my first guide. These chips can ONLY be unlocked by the l5 method. At this point, what you want is a mobile 2500+ - see the if you're in the market for a new cpu thread by danny the bum in reccomendations. Although they run att a lower fsb, they are unlocked, and have MUCH lower voltage (1.25v!!) which = MUCH more oc potential.
Tulatin
Enlightened Master
Enlightened Master
 
Posts: 14664
Joined: Wed Dec 11, 2002 2:29 pm
Location: Canada

Postby subtool » Tue Feb 17, 2004 10:32 am

Hi Tulatin,

You said "these chips can only be unlocked by the l5 method" that is the regular barton 2500+ with a 333fsb that you were talking about, correct? I read the tutorials you had linked in begining of the thread and I am not sure which is the l5 method . I am planning on building a system from ground up and I was wondering which cpu would be better, the 2500+ or the 2500+ mobile. I would like to overclock but probably not to the extent of water cooling, would the 2500+ with 333fsb oc better than the 2500+ mobile without serious cooling? Thanks a ton for your help.

Dave
NF7-S
Barton 2500+
Enermax 430W PSU
MSI FX 5200
2X 256 Samsung DDR 400
subtool
Initiate
Initiate
 
Posts: 50
Joined: Fri Jan 30, 2004 2:29 am
Location: The North, Eh.

Postby Tulatin » Tue Feb 17, 2004 10:34 am

well, the L5 method is not listed in this guide ATM. I will add it soon. and the chips are about the same quality, or should be. Also, the mobile should OC better, due to the ability to get your voltage up to stock 2500+ levels when ocing, with very little heat increases over the stock.
Tulatin
Enlightened Master
Enlightened Master
 
Posts: 14664
Joined: Wed Dec 11, 2002 2:29 pm
Location: Canada

Postby subtool » Wed Feb 18, 2004 3:16 pm

I was reading around a bit and found some more info on unlocking bartons. Do these sources sound resonable or would it be a big risk moding you chip in this way?

L5 method:
http://www.ocworkbench.com/2004/guides/ ... wk43-1.htm

This is a slightly more indepth versoin of the wiretrick mentioned at the begining of this thread:
http://www.athlon-unlock.co.uk/5202/5283.html
NF7-S
Barton 2500+
Enermax 430W PSU
MSI FX 5200
2X 256 Samsung DDR 400
subtool
Initiate
Initiate
 
Posts: 50
Joined: Fri Jan 30, 2004 2:29 am
Location: The North, Eh.

Postby Tulatin » Wed Feb 18, 2004 3:18 pm

the L5 method is safe. It's essentially the pencil trick, but in a different spot - provided you have no ditch that is.
Tulatin
Enlightened Master
Enlightened Master
 
Posts: 14664
Joined: Wed Dec 11, 2002 2:29 pm
Location: Canada

Postby msixp_k7 » Sun May 28, 2006 4:52 pm

Hay I got 1 for you I have an AMD2500+ Barton runig at only 1900+ I set the multyplier all the way up now 2200+ 1779.25 acordin to cpu-z how do I fix that And will doing this mod cause any problems.Name AMD Athlon XP
Code name Barton
Specification AMD Athlon(tm) XP 2200+
Family/Model/Stepping 6A0
Extended Family/Model 7/A
Package Socket A
Technology 0.13um
Instructions Sets MMX, Extended MMX, 3DNow!, Extended 3DNow!, SSE
Features
Clock Speed 1766.8 MHz
Clock multiplier x12.5
Front Side Bus Frequency 141.3 MHz
Bus Speed 282.7 MHz
P-Rating 2200+
L1 Data Cache 64 KBytes, 2-way set associative, 64 Bytes line size
L1 Instruction Cache 64 KBytes, 2-way set associative, 64 Bytes line size
L2 Cache 512 KBytes, 16-way set associative, 64 Bytes line size
L2 Speed 1766.8 MHz (Full)
L2 Location On Chip
L2 Data Prefetch Logic yes
L2 Bus Width 64 bits
msixp_k7
Initiate
Initiate
 
Posts: 40
Joined: Sat May 06, 2006 6:21 am
Location: Puerto Rico

Previous

Return to Overclockers Anonymous

Who is online

Users browsing this forum: No registered users and 1 guest