The Mother Board

Motherboards.org forums. Free tech support, motherboard ID, and more.
It is currently Thu Dec 13, 2018 10:11 am

All times are UTC - 8 hours




Post new topic Reply to topic  [ 228 posts ]  Go to page Previous  1 ... 16, 17, 18, 19, 20, 21, 22, 23  Next
Author Message
 Post subject:
PostPosted: Sat Oct 08, 2005 3:38 am 
Offline
Mobo-fu Master
Mobo-fu Master

Joined: Sun May 06, 2001 12:01 am
Posts: 37464
Location: Netherlands
Gem wrote:
I was transferring all of my goodies to my new Antec p180, which is absolutely beautiful if I might add, and I go to turn it on and after 3 seconds it shuts off. So I double check my Zalman heatsink/fan and see that the 3 pin connector wire is acting as a thermal pad 8O 8O .... weeeeeeee. I have to admit that was funny but only after i made sure the half melted wire was still able to provide current to the fan motor. :oops: :oops:


Back in the socket 7 days, heatsinks sometimes had a rim to make sure you put them on the right way. So, one day we had a system that BSODed all over the place and couldn't find what was wrong. Well, the heat transfer of just a rim isn't enough to cool your CPU :lol:

_________________
We hate rut, but we fear change.
********************************
System error, strike any user to continue...


Top
 Profile  
Reply with quote  
 Post subject:
PostPosted: Fri Oct 28, 2005 4:48 am 
Offline
Green Belt
Green Belt

Joined: Tue Oct 07, 2003 1:13 pm
Posts: 120
Location: Long Island
Lemme just say this one thing. Never go to do anything with your case with the power on. I had just installed a new vid card and wanted to make sure everything was working OK before closing my case back up. Well, everything was fine, so I left the power on and went to put the side panel back on. The screwdriver slipped and went right into the back of my psu, right through the fan grill. Sparks everyewhere, lights in the room flickered, smoke out the back of the PSU. Mustve shorted it out BIG TIME. The worst part is I had just gotten done sleeving all the wires and routing the cables behind the mobo, took me about 3 days to get it perfect while my GF sat there wondering what the hell I was doing. Got a new antec PSU and will always make sure that the power is off from now on!

_________________
topdeckr@optonline.net


Top
 Profile  
Reply with quote  
 Post subject: Boy am I dumb
PostPosted: Fri Nov 04, 2005 10:22 am 
Offline
Black Belt
Black Belt

Joined: Mon Aug 18, 2003 2:06 pm
Posts: 708
Location: Tyler, Texas
I don't know if anyone has posted this yet, but it can't hurt to post it again.

1)Make sure the drive you are formatting is the drive you want to format.
Just because drives are the same size doesn't mean they are the same drive.
2)If you buy a new heatsink/fan for your processor, it is usually a good idea to give the fan power.
I have gone just about a week before I realised my fan was not on. :oops:
3)My Favorite, when installing a DVD Burner, or I guess any CD/DVD type drive, put it in right side up. The DVDs definitely won't burn that way.

Sure this may seem overly stupid, but I know I am NOT a smart guy.
BTW, all of this was done by me in the period of a week.

_________________
Fold Team 33258


Top
 Profile  
Reply with quote  
 Post subject:
PostPosted: Tue Nov 15, 2005 5:13 am 
Offline
Black Belt 5th Degree
Black Belt 5th Degree

Joined: Tue Jul 10, 2001 12:01 am
Posts: 5491
Location: Flintshire, U.K
Here's some of the things I've managed to do. :oops:

1. Put the power plug into a floppy drive the wrong way round...ruined

2. Put Cache chips for 486 board in the wrong way round and I'd just driven 70 miles to pick them up.

3. Placed a Bios chip in the wrong way round and broken legs on several of them as well.

4. Destroyed at least 3 AMD Duron/Athlon CPU's by not being careful enough while putting the fan/hs on, plus another that I forgot to plug the fan in.

5. Snapped off the power plug and half the 40 pin slot on a 40gig HD that I bought about 30 minutes before. I was able to repair it though.

6. Left a small screw on a mobo in a desktop I once had, took ages to find out what the problem was.

7. Knocked off a small jumper on a Tape Drive and put it back in the wrong place, totally destroyed it.

8. Left some cables too close to the fan, they got sucked in and broke a blade.

9. Put a GeForce2 card into a Socket 7 board, lasted about 10 seconds.

10. Constructed an entire computer then found out there was no way I could get the floppy drive cable on without removing the motherboard again. I always fit the cables to the board beforehand now.

Pete

_________________
Image


Top
 Profile  
Reply with quote  
 Post subject:
PostPosted: Tue Nov 15, 2005 7:14 am 
Offline
Black Belt 2nd Degree
Black Belt 2nd Degree

Joined: Tue Jun 29, 2004 9:05 am
Posts: 2792
Location: St. Augustine, Fl
heres an installation fault..
Relationships +

EDIT

oopsss... didnt mean to post it just wanted to write it and get it off my chest and rant to myself.


Top
 Profile  
Reply with quote  
 Post subject:
PostPosted: Wed Nov 30, 2005 5:36 pm 
Offline
Pilgrim
Pilgrim

Joined: Sat Oct 29, 2005 1:29 pm
Posts: 11
Location: Wisconsin U.S.A.
Install a pci modem (with slight modifications) into an isa slot & wonder why it dosent work. LOL


Top
 Profile  
Reply with quote  
 Post subject:
PostPosted: Wed Nov 30, 2005 9:57 pm 
Offline
Mobo-fu Master
Mobo-fu Master

Joined: Sun May 06, 2001 12:01 am
Posts: 37464
Location: Netherlands
tvthegreat wrote:
Install a pci modem (with slight modifications) into an isa slot & wonder why it dosent work. LOL


is that yours or something you encountered in a machine?

_________________
We hate rut, but we fear change.
********************************
System error, strike any user to continue...


Top
 Profile  
Reply with quote  
 Post subject:
PostPosted: Wed May 31, 2006 8:31 pm 
Once I forgot to put the Thermal Gel / paste / pad in between my socket 754 AMD 3000+ and my heatsink... It lasted about 1.5 hours before it flatlined.


Top
  
Reply with quote  
 Post subject:
PostPosted: Wed Jun 21, 2006 8:51 pm 
How do i find out what kind of mother board i have and im having alot of problems building my pc


Top
  
Reply with quote  
 Post subject:
PostPosted: Thu Jun 22, 2006 2:15 am 
Offline
Black Belt 3rd Degree
Black Belt 3rd Degree

Joined: Sat Jul 24, 2004 12:34 pm
Posts: 3430
Location: UK
Cloud950mhz wrote:
How do i find out what kind of mother board i have and im having alot of problems building my pc


Welcome to motherboards :-)

You need to post this in the motherboard identification forum and read the stickies there so that you can give us the information we need to help you.

Also read the stickies in Tech Support on troubleshooting and post there with your specific problem.....give as much info as possible.

http://www.motherboards.org/forums/viewforum.php?f=2

(or may a kind mod will notice and move it for you)

_________________
"that's some catch that Catch 22"
"It's the best that there is"

Image


Top
 Profile  
Reply with quote  
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 228 posts ]  Go to page Previous  1 ... 16, 17, 18, 19, 20, 21, 22, 23  Next

All times are UTC - 8 hours


Who is online

Users browsing this forum: AhrefsBot [Bot] and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group