The Mother Board

Motherboards.org forums. Free tech support, motherboard ID, and more.
İstanbul Escort Bayan
It is currently Mon Jun 24, 2019 9:53 am

View unanswered posts | View active topics





Post new topic Reply to topic  Page 1 of 1
  [ 9 posts ] 
  Previous topic | Next topic 
Author Message
theVodkaCircle
PostPosted: Wed Jun 26, 2002 4:51 pm 
Offline
Pilgrim
Pilgrim

Joined: Wed Jun 26, 2002 4:43 pm
Posts: 9
Location: Sydney, Australia
Hi all, great site, glad I found it.

I am in the limbo land of being a few months away from affording new bits for my PC and want, in the interim, to be able to juice my existing one up a little if possible.
What I have.....
Gigabyte Intel AGPSET 440BX BX2000 1.6 motherboard
Award ROM PCI/ISA BIOS 2A69KG0E (Theres a 4.51PG in there somewhere too)
Intel Celeron 466 CPU
Gigabyte TNT2 32Mb Video Card

I have been doing some research but for someone who has never looked into overclocking previously, I am a little confused to be honest.

I have read a suggestion of increasing through BIOS the CPU speed.
(Celeron 466 Mhz - 581 Mhz @ 7 x 83 Mhz or also 525 Mhz @ 7 x 75 Mhz)
Does anyone have any suggestions please ?

Thank you.

Also, with the vid card, I have thought that it is also overclockable. I would assume through software but haven't been able to, as yet, find the correct software. Would I be right in assuming it would come with drivers ?

Cheers
Top
 Profile  
Reply with quote  
The Disturbance
 Post subject:
PostPosted: Wed Jun 26, 2002 5:03 pm 
Offline
Black Belt
Black Belt

Joined: Mon May 27, 2002 6:44 am
Posts: 719
Location: RI
Well for the video card use PowerStrip download it here: http://download.com.com/3000-2094-10121 ... ag=lst-0-1
don't go too high on the card I let my GeForce2 MX400 stay at

Engine- 186.13MHz
Memory- 177.95MHz (both are in the yellow area)

With that I can get 3000 on 3DMark2001 SE...see my sig...
I would run it higher, but my video card doesn't have a fan or heatsink... :cry:
Top
 Profile  
Reply with quote  
theVodkaCircle
 Post subject:
PostPosted: Wed Jun 26, 2002 6:05 pm 
Offline
Pilgrim
Pilgrim

Joined: Wed Jun 26, 2002 4:43 pm
Posts: 9
Location: Sydney, Australia
Great, thanks for that, d/ling now.

This will help somewhat I hope. Now for the mb/cpu...... :)
Top
 Profile  
Reply with quote  
Tolemac
 Post subject:
PostPosted: Wed Jun 26, 2002 7:39 pm 
Offline
Mobo-fu Master
Mobo-fu Master

Joined: Tue Sep 12, 2000 12:01 am
Posts: 14276
Location: L-1 Bridge
Go ahead and set the FSB to 75MHz and reboot your unit. If it goes to 525MHz for the CPU, then there you are. Run some apps to see if it's stable and if it is, then you have an overclocked system. 8)

_________________
The Gift of Healing
Conscious Energy Meditation
Top
 Profile  
Reply with quote  
theVodkaCircle
 Post subject:
PostPosted: Wed Jun 26, 2002 7:48 pm 
Offline
Pilgrim
Pilgrim

Joined: Wed Jun 26, 2002 4:43 pm
Posts: 9
Location: Sydney, Australia
Dopey question approaching......
Set the FSB ?
Sorry, dont answer that until I can get home and actually LOOK in bios :)
But on the other hand, forewarned.....
If youre familiar with the award bios I listed above, do you know what section in bios will have these settings please ?

Cheers everyone.
Top
 Profile  
Reply with quote  
Tolemac
 Post subject:
PostPosted: Wed Jun 26, 2002 9:28 pm 
Offline
Mobo-fu Master
Mobo-fu Master

Joined: Tue Sep 12, 2000 12:01 am
Posts: 14276
Location: L-1 Bridge
Do you have the manual for that mobo? It may not be in the BIOS as it is an older board. It may be that you will need to set the Front Side Bus (FSB) by using jumpers on the board itself.

_________________
The Gift of Healing
Conscious Energy Meditation
Top
 Profile  
Reply with quote  
theVodkaCircle
 Post subject:
PostPosted: Thu Jun 27, 2002 4:09 pm 
Offline
Pilgrim
Pilgrim

Joined: Wed Jun 26, 2002 4:43 pm
Posts: 9
Location: Sydney, Australia
Hehheh, Im in the middle of packing to move. I think I will check Gigabytes web site and see if they have pdf version :)
Cheers for your help everyone.
Top
 Profile  
Reply with quote  
Toby B.
 Post subject:
PostPosted: Fri Jun 28, 2002 12:18 am 
Offline
Lead Mobo-fu Master
Lead Mobo-fu Master

Joined: Sun Dec 16, 2001 1:01 am
Posts: 14303
Location: Maine
Manuals:

PCB Rev. 1.0
http://ftp.gigabyte.com.tw/support/user ... 0799_m.pdf

PCB Rev. 1.1
http://ftp.gigabyte.com.tw/support/user ... 2999_m.pdf

Toby

_________________
Compaq-Fu Master
Ctechinfo funding drive information
Top
 Profile  
Reply with quote  
theVodkaCircle
 Post subject:
PostPosted: Wed Jul 03, 2002 8:54 pm 
Offline
Pilgrim
Pilgrim

Joined: Wed Jun 26, 2002 4:43 pm
Posts: 9
Location: Sydney, Australia
Toby you are a LEGEND. Thanks a lot.
Top
 Profile  
Reply with quote  
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 9 posts ] 


Who is online

Users browsing this forum: No registered users and 3 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group