Page 7 of 9

PostPosted: Mon Oct 26, 2009 4:03 pm
by AmEv
Good, very good.

I don't know if you intended it or not, but the PSU fan behind the "gears" seems to give it a Swastika look.

*In a good way :roll: :lol: :wink:

PostPosted: Sat Oct 31, 2009 3:51 am
by Mnpctech.com
I didn't even notice that! Thanks for commenting

Our HD arrived, Western Digital Caviar Blue WD2500AAJS 250GB 7200 RPM 8MB Cache SATA 3.0Gb

$44.99 shipped!

http://www.newegg.com/Product/Product.a ... 6822136113

Image

PostPosted: Mon Nov 02, 2009 6:22 pm
by Mnpctech.com
Nate started the system install Sunday afternoon. The Thermalright Ultra 120 Extreme Revision A HSF clears the chassis.
Image

250mm fan draws out the warm air from the Ultra 120 Extreme Revision A
Image

Image

Thermalright has since updated the mounting bracket to turn the HSF 90 degrees and avoid blocking DDR in first two slots
Image

We'll be using these new PC Cable management clamps
http://www.mnpctech.com/CableClamp.html

Image

Nate from CustomPCMax.com
Image

PostPosted: Tue Nov 03, 2009 4:30 am
by Mnpctech.com
Nate and I agreed top of Heat sink fins looks naked, it needs something... More on that later :thumb:

Image

PostPosted: Wed Nov 04, 2009 4:40 pm
by Mnpctech.com
We'll be painting the 5.1 surround sound headset we received from Psyko Audio with matching camo

Image

PostPosted: Wed Nov 04, 2009 8:13 pm
by THRASHER2
Those are some KOOL head-phones :)

PostPosted: Fri Nov 06, 2009 10:36 am
by Mnpctech.com
The dissection of a Psyko Audio Headset, before prepped for Camo paint

The padded ear cup pads can be popped off with their pivoting bases (grab around the top of the plastic ring and pull it out).

Image

Image

Image

Image

4 screws total, 2 on each side fasten on outter Silver trim piece

Image

4, screw locations to be removed.

Image

Image

Image

The clear cup cover is easily removed, once the outter trim piece is removed.

Image

The clear cover pops off (push a small flat head screw driver into the gaps to pry off).

Image

Image

The pads are peeled off. I used a small flat head screw driver to pry up the edge first.

Image

You can peel off the top 5 pads to reveal 5 screws holding on the top Silver cover.

Image

Image

Image

5x 30mm diam. 32 ohm. speakers project sound into your skull

Image

PostPosted: Sat Nov 07, 2009 5:12 am
by Mnpctech.com
I agree! After the pads are removed, the headset is re-assembled before being masked off before camo paint job. It's easier to apply the camo stencils when it's all assembled without the pads

Image

PostPosted: Sat Nov 07, 2009 5:21 pm
by Mnpctech.com
For tidying up the PSU cables, I'm using the small size PC Cable Clamps, they hold approximately 1" bundle

PC Cable Clamp Link
http://www.mnpctech.com/CableClamp.html


Image


Image


Image


Image

PostPosted: Thu Nov 12, 2009 1:54 pm
by Mnpctech.com
Brad sent me progress on the Camo paint on the Pysko Audio head phones. These will look awesome!

Headset
Image

Amp
Image

Mic
Image