Page 2 of 9

PostPosted: Wed Jul 18, 2007 8:24 pm
by THRASHER2
Here is a pic of the side panel that i drilled the holes for the Spinner bracket.
Image

Bracket mounted with macking tape removed.
Image

The Spinner is Mounted :haha:
Image

More on the way............Stay tuned :excited:

PostPosted: Wed Jul 18, 2007 8:25 pm
by THRASHER2
Watch out the Madman is at it Again :haha:
Image

A little taping off and sizing up the Holes :shades:
Image

And the work begains :scared:
Image

Image

PostPosted: Wed Jul 18, 2007 8:26 pm
by THRASHER2
BAM!!!!!!
I made all the cuts on the Panel (Reset switch/Power Switch/Switch Panel and Spinner Hole)
Image

Installed the Bling to see how it fits (WOW)
Image

Front panel with the switches up
Image

Close-up view of the BLING!
Image

PostPosted: Wed Jul 18, 2007 8:28 pm
by THRASHER2
Here is another Pic of the BLING installed on front of the Case.
Image

Here is the Modded LCD fan controller done by Twisted
[quote=Twizted]It looks better IRL as the camera kinda makes it look orangish but it looks good for sure;)

Image
Image[/quote]

Stay tuned for the next weeks episode (AS THE SPINNER TURNS) :haha:

PostPosted: Wed Jul 18, 2007 8:31 pm
by THRASHER2
Here is the latest updates on the Spinner Mod :blurp:

Ok.....I needed to cut the small spinner housing
First look
Image

I cutted the spinner housing down to fit into the Case body
Image

Here is where i was marking the holes to be cut
Image

T2 in Action :haha:
Image

Checking the cuts i just made (Test Fit)
Image

PostPosted: Wed Jul 18, 2007 8:31 pm
by THRASHER2
BAM!!!!
Isn't it pretty :blurp:
Image

Close-up of the cleaned up cuts :shades:
Image

Off to the back of the case for the 80mm fan test fit
Image

I installed some U-Channel Trim Molding on the 80mm fan holes (and did a Grill test fit)
BAM!!!! I LOVE IT! :excited:
Image

More to come...........Stay tuned :thumbsup:


PostPosted: Wed Jul 18, 2007 8:31 pm
by THRASHER2
The Mod Garage project is finished for now (Thank God that's Done)
I have time for the Spinnner Mod Now :grin:


Ok.....Back on track
First up
Cleaning up the Oval hole where the Power Switch goes.
Image
(Sorry for the Pic) Damn work camera :sad:

Image

A little work and BAM!!! (That Crap dries Quick)

Image

PostPosted: Wed Jul 18, 2007 8:32 pm
by THRASHER2
I was checking out the Spinner side panel (DAMIT! the upper cut was to High to the Edge)
Image

Image
Lucky ...I have another Case with that side Panel.

Here are the two Panel together
Image

I had another sweeet idea :haha: (Added a chrome Frame to the top)
Image

The layout for the Cut (Alot of corners) :eek:
Image

PostPosted: Wed Jul 18, 2007 8:32 pm
by THRASHER2
Super Update!!!!!
I am upgrading the Cpu/Mobo and Video card for this Project :shades:

My SAPPHIRE PURE Innovation PI-A9RX480 MoBo came in Today
Cpu/Video Card to follow :drool::blurp::excited:

Image

CPU Type: Athlon 64 FX/Athlon 64/Sempron
DDR Standard: DDR 400 (PC 3200)
Dual Channel Supported: Yes
FSB: 1000MHz Hyper Transport (2000 MT/s)
Maximum Memory Supported: 4GB
Number of DDR Slots: 4x 184pin DDR
PCI Express x1: 2
PCI Express x16: 1
PCI Slots: 2
South Bridge: ATI SB450
Model #: PI-A9RX480


Small update :thumbsup:

I ordered some new parts for the project. w00ts :excited:
SAPPHIRE Radeon X850XT 256MB GDDR3 PCI Express x16 Video Card
Image

$119.99 ($89.99 after $30.00 Mail-In Rebate)

PostPosted: Wed Jul 18, 2007 8:34 pm
by THRASHER2
The MaD Man is back at work :haha: (7hours of some sweeet modding)
I did a ruff cut of the upper Square section

Image

Cleaned up all the cuts
Image



Modding In [url="http://smg.photobucket.com/albums/v629/THRASHER2/?action=view&current=ActionMan.flv"]Action[/url]